Fingerprint electronic lock how to install fingerprint electronic lock installation method tutorial

How to install fingerprint electronic lock? Fingerprint electronic lock installation need to pay attention to what? Fingerprint Electronic Lock Installation Method Tutorial. The installation of the fingerprint electronic lock is a must-completed step before use. Only a reasonable fingerprint lock can be used for better operation. Fingerprint electronic lock installation steps include preparation before installation, removal of the old lock body (new security door installation does not include this step), install a new lock body, install the panel, before and after the installation plate, fingerprint lock function settings debugging. IX2 Smart Lock China

2017-05-17_091651.jpg IX2 Smart Lock China

Fingerprint electronic lock door opening direction selection and installation preparation

When we are installing, we must determine the direction of opening. Most of them are now open to the right. Here we also use this list. Of course, small partners can also choose other directions. IX2 Smart Lock China

The first step: check and judge the target IX2 smart lock China

First, check the type of the target door, and then whether the effective installation width of the installation lock position reaches the width of the fingerprint lock lock body, and whether the final result of the installation solution can be accepted by the customer. If these conditions are correct, you can continue with the following steps. IX2 Smart Lock China

Step 2: Measure several key parameters of the old lock on the door IX2 Smart Lock China

Through the above measurements and observations, remember the parameters, to determine whether you need to customize the side panel, if the original anti-theft door side trim is not a standard 30*240 or 24*240, generally need to build, the cost is about 50 yuan about. IX2 Smart Lock China

The third step: remove the original lock IX2 smart lock China

Determine the original door material, specifications, and the original lock related parameters and ready to install accessories, remove the original lock and store it in a box, the customer custody, if the fingerprint lock needs to be removed for maintenance, you can then install the original lock Perform a temporary replacement. IX2 Smart Lock China

Step 4: Install a new lock body and lock cylinder IX2 Smart Lock China

After dismantling the old lock body, install the lock body of the fingerprint lock (you need to install the side plate for the side trim plate of the customized side trim plate), hang the heaven and earth bar, and then use a screw to fix it. Next, insert Fangpu's high-security cylinder into the lock cylinder hole and use a special screw to insert and tighten it from the side and fix the cylinder. After fixing, use the key to insert the lock cylinder and turn the lock cylinder to test whether the lock body can be opened and whether the lock is normal. IX2 Smart Lock China

Fingerprint electronic lock body installation steps

1. Make sure that the direction of the bolt is consistent with the door opening direction. If it is not, some anti-theft locks can be adjusted. Use a screwdriver to push the latch up. After turning 180°, release the screwdriver to reset it. IX2 Smart Lock China

2. Then put the lock body into the opened door hole with the beveled end as the upper end, let the lock body line pass out of the front door hole from the upper end door hole, and then use the screw to lock the lock body. IX2 Smart Lock China

3. Put the lock cylinder into the lock body hole from the outside of the door, and fix the lock cylinder with the lock screw. At this time, the lock body is completely installed. Use the mechanical key to test whether the lock body tongue is working properly, and then install the panel. . IX2 Smart Lock China

Fingerprint electronic lock panel installation method

1. Before installing the panel, press the door to open the handle and keep the front and back panels parallel to the door. Do not skew the left and right distances so that the handle is aligned with the horizontal direction of the lock body. Adjust the vertical distance so that the vertical direction of the handle is consistent with the lock body. IX2 Smart Lock China

2. First put the front rod into the lock body hole from the outside, and then insert the lock body line into the panel bus line, and the public line through the door hole to the back of the door, then put the square spring into the handle hole Align the front panel handle hole with the front rod, then install the back panel from the inside of the door and fix the back panel and front panel to the door with screws. IX2 Smart Lock China

3. Then put the rear rod into the square hole of the lock body from the inside of the door, put the spring into the handle hole of the rear panel, and plug the connection line of the rear panel with the public line of the front panel. IX2 Smart Lock China

4. Insert the excess wire into the entry hole, and then place the front panel on the back lever and secure it with the screw. IX2 Smart Lock China

5. Then insert a four-section No. 5 alkaline battery to test the entire lock installation and function. IX2 Smart Lock China

Fingerprint Electronic Locking Box Buckle Installation Tutorial

1. After the fingerprint lock test is normal, the buckle box and the buckle plate can be installed on the door frame. Note the direction of the lower end of the buckle plate, and the square hole is at the upper end. IX2 Smart Lock China

2. Then open and close the door to check whether the closing of the button box and the bolt door frame is normal. Note that it is best to have someone inside and outside the door to prevent the door from opening during testing. This completes our door lock installation. IX2 Smart Lock China

2017-05-17_091651_72x72.jpg IX2 Smart Lock China

Fingerprint electronic lock installation precautions

1) Because the door opening method is not the same, the holes on the mounting mold are not the same, so be sure to determine the correct position before installation. IX2 Smart Lock China

2) Lock front and rear body wires, sockets and plugs to ensure the correct connection. IX2 Smart Lock China

3) Before installation, determine the installation height. Place the mounting module in the appropriate position and use a pencil to draw the position of the hole. IX2 Smart Lock China

4) When the hole is drawn, the flange of the mounting mold must be perpendicular to the door frame. Otherwise, the lock body cannot be installed perpendicular to the door. IX2 Smart Lock China

5) The lock core is generally required to be installed in the middle of the door thickness. IX2 Smart Lock China

6) After opening the hole in the door frame, be sure to clean the wood chips or other foreign objects inside the hole to prevent the door from dropping the debris into the lock body when the switch is vibrating. IX2 Smart Lock China

The new fingerprint lock generally does not have fingerprints and passwords or cards. However, it is best to enter the management mode before use. Run the initialization operation to ensure that the lock settings are restored to the factory default values ​​and clear the original data. After the initialization is completed, the user's administrator fingerprint and other information are entered. IX2 Smart Lock China

The above content is published by the smart lock China Network Xiaobian, please pay attention to us for more fingerprint lock installation problems! IX2 Smart Lock China

Heat exchanger Tube
Heat exchanger Tube are used in all types of process industries. We offer the market`s widest selection of stainless steel grades and has extensive experience of manufacturing heat exchanger tubes.
Description: Heat-exchanger equipment, pipelines and pipeline components
OD: 15.88, 19.05, 25.4, 31.75, 38.1mm etc;
WT: 1.24, 1.65, 2.11, 2.77, 3.05mm etc;
Main Testing Terms Accoring to ASTM A213 and ASTM A1016, EN 10216-5
1. High pressure hydraulic Test / Hydrostatic testing; 2. Eddy current test, Ultrasonic Test; 3. Mechanical Test, Physical properties test; 4. OD , WT, Length tolerance Test.; 5. PMI Test
Tubes End: The tubes are supplied plain, square cut and on request, the tubes will be deburred.
Application:
Nuclear Industry; Chemical Industry; Petrochemical industry; HVAC (Heating Ventilation Air Conditioning), refrigeration; Food and Beverages; Power Generation

2013050915065676 2013050915072546 2013050915075349 2013050915081997


Heat Exchange Tube

Heat Exchange Tube,Incoloy Heat Exchanger Tube,Inconel Heat Exchanger Tube

YUHONG GROUP CO.,LIMITED , https://www.alloypipeline.com