Multifunctional pump control valve technical requirements introduction

This standard applies to the nominal pressure PN1.0MPa-PN4.0MPa, nominal diameter of DN50mm-DN1200mm multi-function pump control valve. The standard technical requirements are introduced as follows: 1. Pressure - temperature level Multi-function pump control valve pressure - temperature rating by the shell, inner parts and control pipe system material pressure - temperature level to determine. The maximum allowable working pressure of multi-functional pump control valve at a certain temperature takes the small value of the maximum allowable working pressure value of shell, inner part and control pipe system material at this temperature. Iron shell pressure - temperature level should be consistent with the provisions of GB / T17241.7. Steel shell pressure - temperature rating should be consistent with the provisions of GB / T9124. For GB / T17241.7, GB / T9124 not specified pressure - temperature grade materials, according to the relevant standards or design requirements. 2. Valve Body Flange Flange and the valve should be cast as a whole. Iron flange type and size should be consistent with the provisions of GB / T17241.6, the technical conditions should be consistent with the provisions of GB / T17241.7; steel flange type and size should be consistent with the provisions of GB / T9113.1, the technical conditions Should comply with the provisions of GB / T9124. 3 valve cover diaphragm seat and diaphragm seat, diaphragm seat and valve body connection type should be flanged. Diaphragm seat and the valve body to connect the number of bolts shall not be less than four. Valve cover and diaphragm seat minimum wall thickness by 2.3 requirements. Valve cover and diaphragm seat flange should be round. Flange sealing surface type can be flat, convex or concave type. 4. Stem, slow closing valve plate, the main valve plate slow closing valve plate and stem should be connected and secure. Slow closing valve plate and the main valve plate sealing type should be sealed metal type. The main valve plate and stem must slide flexible and reliable. The main valve plate and the main valve plate seal can be sealed with metal and non-metallic two types of seals. 5. Diaphragm diaphragm appearance quality should be consistent with the provisions of HG / T3090. When applied to drinking water, the diaphragm material safety should be consistent with the provisions of GB / T17219. 6. Control pipe system Control system components should be able to withstand the highest pressure on the valve, no leakage of all parts. 7. Material Selection of the main components of the material should be JB / T5300 requirements. Copper alloy castings shall comply with the provisions of GB / T12225; gray cast iron castings shall comply with the provisions of GB / T12226, the tensile strength of not less than 200MPa; ductile iron castings shall comply with the provisions of GB / T12227; carbon steel castings shall comply with GB / T12229 provisions; austenitic steel castings should be consistent with the provisions of GB / T12230. Steel multi-function pump control valve casting appearance quality should be consistent with the provisions of JB / T7927, iron multi-function pump control valve casting appearance quality reference JB / T7927's. 8. Housing strength Multifunctional pump control valve shell strength should be consistent with the provisions of GB / T13927. 9. Sealing performance Multifunctional pump control valve sealing performance should be consistent with the provisions of GB / T13927. 10. Cleanliness Multipurpose pump control valve cleanliness should be consistent with the provisions of JB / T7748. 11. Painting When applied to drinking water, multi-functional pump control valve cavity coating material safety should be consistent with the provisions of GB / T17219. Painting the outer surface is not specified, special requirements specified in the order contract.

UNI Flanges

UNI style of flanges:
Plate (UNI 2276 2277 2278 6083 6084) ,Blind (UNI6091 6092 6093 6094 6095 6096 6097) ,Threaded (UNI2253 2254), Welding-Neck (UNI2280 2281 2282 2283 2284 2285 2286)
Pressure rating:
PN 6 PN10 PN16 PN25 PN40 PN64 PN100

Features

Dimensions:
UNI AND DRAWING
Carbon Steel Materials:
ASTMA105-ASTMA350LF2/ASTMA694 F42-F52-F60-F65-70/C22.8/C21/Rst37.2/S235JRG2/P355NH/SS400
Alloy Steel Materials:
ASTM A182 F1-F11-F12-F22-F5-F9-F91
Stainless Steel Materials:
ASTM A 182 F304/304L/304H-ASTM A182 F321/321H-ASTM A182 F347-347H-ASTM A182 F316-316L-316H
Special alloys:
DUPLEX-SUPER DUPLEX-INCONEL-INCOLOY-MONEL-HASTELLOY-TITANIUM

UNI Flanges,UNI Blind Flanges,UNI EN Flanges,Flat Faced Flange

Shandong Zhongnuo Heavy Industry Co.,Ltd. , https://www.znforged.com