Nowadays, almost all houses sold by real estate developers are rough houses, which means that we need to renovate the house when we get it. For the decoration of the rough house, many people are not sure what the rough house decoration steps are, and the most critical one is It ’s wall decoration, and it ’s confusing from step to step, especially in some details, it ’s really done and forgotten, hey, tired! The same is true for the head of the household. I am afraid that the workers deceived us and we did n’t understand anything. We cut corners and cut materials during the wall decoration of the rough room. As a result, it took only a few days for the wall decoration to be completed. Do n’t worry, the workers and the heads of households have all come to see them together. Today, I will elaborate on what the rough wall decoration steps are. Step 1: Finished product protection Generally, woodworking furniture and ceramic tile laying should be completed before the wall treatment. If it is a second-hand house renovation, there may be more finished products. In order to prevent the finished product from being contaminated by wall skin, dust and paint during the treatment of the wall surface, the existing finished product in the room should be carefully protected, otherwise it will be too late to regret once the loss is caused! Step 2: Check and deal with the current status of the wall Different wall inspection methods are different, mainly in the following three situations: 1. Cement wall It should be thoroughly checked whether the concrete wall surface to be painted is solid and smooth. If the wall surface is not strong enough or there are large cracks and holes, it is recommended to complain to the developer or the property and request it to be redone or repaired. â– Method to check whether the old wall is strong: â–ª Visually check for peeling, cracking, and drumming, if not, it is not strong; â–ª Look for a blunt instrument (such as a small hammer) and knock on the wall to check whether there is an empty drum, if not, it is not strong; â–ª Splash some water after polishing the latex paint, shovel it with a spatula to see if it is easy to shovel. 2. White wall Many commercial houses are now white walls when they are handed over. It may seem that the cleanliness may actually cause more hidden dangers. First of all, you must check the firmness of the walls to see if the white materials are water resistant. If it is not water-resistant or water-resistant, from the perspective of long-term use, it should be shoveled and redone; as a short-term use, it can also be retained, but it is best to do it again and then perform other steps. At the same time, the wall should also be checked for empty drums as a whole. If there are empty drums, they must be shoveled. â– Water resistance test method of white wall: Find a wall, pour a little water and rub it with your hands to see if it will become white mud. â–ª If you can pierce the white layer completely with your hands, it will have no water resistance. â–ª If your hands stick to white when rubbed, but you cannot destroy this layer of white material, it means that the material has a certain water resistance, you can find more points to test. â–ª If the hand is rubbed, the hand is almost white and not sticky, which means that the water resistance is very good. 3. The wall has been decorated Refers to the wall surface has been decorated with wallpaper or latex paint, which is a common situation in second-hand houses. Generally speaking, the original surface decoration should be cleaned out before this kind of secondary decoration. If it is wallpaper, the wallpaper should be removed first; if it is latex paint, the latex paint should be polished first. After the surface decoration is removed, depending on the water resistance, it is decided whether to shovel the wall. Step 3: Sealing layer treatment After the first two steps, we have made enough preparations (if you need to shovel the wall, it should have been shoveled at this time), the wall can be sealed below. Wall sealing includes two aspects: ⶠFilling in cracks, slots, holes, this is just a repair gypsum product; â· The curing of the base layer of the wall, this is usually done with a curing agent or curing glue, and there are some situations that need to be solved with a patch (kraft paper) with stronger curing ability. Let me talk a little bit here: The first is the curing agent. The curing agent has liquid, such as various glues, concrete interface treatment agents (interface agents for short), and dry powder. It can be used after dilution with water, such as dry powder curing agent. In terms of environmental protection, dry powders generally have lower harmful content. The second is kraft paper. Kraft paper is a more advanced sealing method, and the cost is higher. Generally, it is not necessary to do the wall surface. However, for thermal insulation walls, looser walls, and cracked walls , the effect is more obvious and should be considered for use. If the cloth (kraft paper) has been attached, there is no need to be a curing agent, and the functions of the two have overlapped. Step 4. Leveling layer processing There are two types of screed treatment: thick screed treatment and fine screed treatment . ⶠThick screed treatment It means that after the wall is sealed, if the flatness of the wall is more than 5mm, it is recommended to use thick leveling material for thick leveling in order to make leveling more convenient. Thick leveling materials are generally scraped once, as long as they are not too thick, as long as they can be leveled. â·Fine leveling treatment When the flatness of the wall surface is less than 5mm, it can be leveled with fine leveling materials. The fine leveling material is generally scraped 2-3 times in batches, and it should be as uniform and smooth as possible. In order to get a better performance when painting, the fine leveling materials are generally polished once with fine sandpaper to make the wall smoother and smoother. If you don't plan to paint, you don't need to polish. Step 5. Brush primer If you want to paint, after leveling, clean the floating dust left on the wall, you can apply the primer. Just apply the primer once, and make sure it is even. After it dries (2-4 hours), you can proceed to the next step. Step 6: Brush the top coat In general, the topcoat should be brushed twice, and each time should be separated by more than 2-4 hours (depending on the surface drying time). After it is basically dry, brush again. After finishing the second pass of the top coat, it will take 1-2 days to dry completely. Pay attention to waterproof, drought-proof and sunscreen before the paint is completely dry to prevent problems with the paint film. Step 7. Acceptance The finished wall should be solid, flat, vertical between yin and yang, no cracks, no holes, uniform color, full paint film, etc. At the same time, pay attention to check the protection of finished products. Well, I do n’t know if you have understood so much, did you understand? Regarding the rough house decoration steps , not only the walls, but also the details, especially the reasonable selection of materials and inspection methods must be thorough, so that after each step is qualified, the next step is carried out benign To be perfect. What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount Laser product Compatible for Mazak
Laser electrodes, nozzles are CNC plasma cutting machine daily operations largest consumables consumption, especially imported electrode and nozzle. Therefore, effectively extending the life of the cutting electrode and the nozzle, will greatly reduce the plasma cutting production costs. Our laser nozzles are made by imported high-quality copper and use superb CNC technology. So they got bright surface and cutting speed, less wear and tear, as compared with the original parts, we can reach 90%. But our low prices, it is worth buying.
Laser product Compatible for Mazak ,, 46603350508 Nozzle 0.8mm,4660335011T Tapered Nozzle EDAWELD COMPANY LIMITED , https://www.jsedaweld.com