Gas stove use failure and troubleshooting

Gas stoves are kitchen appliances that we use every day. However, in the winter, some families' gas stoves often have small flames and sometimes they can't catch fire. If consumers encounter these problems, don't blindly disassemble them. Check, the experts gave us a detailed answer to these common problems, if you encounter problems with the use of gas stoves, may wish to pay attention:

What should I do if I use a liquefied petroleum gas gas stove?

The normal flame of the LPG gas stove is light blue, the flame inside the flame is clear, the height is about 20mm, there is slight noise, and the firepower is strong. If the flame is small, the reasons and troubleshooting are as follows:

1), the burner fire cover fire hole is blocked by dirt, hindering the combustor mixed gas outflow, cleaning the fire hole dirt.

2) The nozzle is clogged and the nozzle is unscrewed and cleaned.

3) The regulator inlet and nozzle are blocked by rust, which hinders the outflow of gas from the bottle and replaces the qualified regulator.

4), the hose is flat and the ventilation is blocked, and the hose is straight.

5), in addition to the gas is about to be used, the valve is not fully open, etc. should also pay attention to, can take corresponding measures to solve.

Why does the gas stove in winter become smaller?

Is the red fire in the gas stove normal? Why is there a red fire in the burning stove?

The red fire in the gas stove is mainly caused by the following reasons:

1), gas cause: When the combustion gas contains more water or too much impurities, the flame color will be red.

2), dust causes: When there is dust or cooking in the house, the amount of moisture and oil in the air increases, it is also prone to red fire.

3) Reasons for the damper: When the damper is not well adjusted, this may happen. In this case, you only need to adjust the damper.

4), the reason of the pot holder: Because the enamel surface of the pot holder is heated at a high temperature, the color of the enamel is red. Because the special material of the enamel is found around the pot holder, the flame is red, which is the color of the metal ion under high temperature.

Therefore, the red fire when burning is not a problem with the stove, but it is caused by the above reasons, it will not affect the normal use, and will not cause harm to human health.

What should I do when I encounter a gas stove that has not been able to catch fire?

If you encounter a gas stove that does not catch fire, you should check it as follows: First, check if the air source switch is in the open state. If it is in the open state, then check if the connecting hose is flat. Or press the bend, if it is not flattened or bent, then, finally, pick up the pot holder and see if there is fire at the ignition nozzle:

1) If there is no fire, look at whether the discharge needle discharges a. If the discharge needle does not discharge, it indicates that the discharge needle is faulty and the discharge needle should be replaced. b. If the discharge needle is discharged, it indicates that the valve body is faulty and the valve body should be replaced.

2) If there is fire: a. If it can burn normally, it means that the position of the igniter is too high, the user should be instructed to gently press the igniter down a few times, and then put on the pot holder. b. If the fire is too hot, but the flame is too weak to reach the burner, the gas pressure is too low. The user of the liquefied gas stove recommends replacing the new pressure reducing valve. The coal gas and natural gas should be reflected to the gas supply company. c. If there is fire, and the flame can reach the fire cover, but it does not catch fire, it means that the valve body is blocked, and the user is instructed to clear the nozzle with fine wire.

Fiberglass Measuring Tape

Fiberglass Measuring Tape,Fiberglass Tapes Measure,Fiberglass Tape Measure,Plastic Fiberglass Measuring Tape

Shangqiu Hengli Measuring Tools Co.,Ltd , https://www.jjmtools.com