Tiles to buy the big secret of the most practical purchase common sense

The purchase of ceramic tiles is very particular. From the style of the home to the material of the tiles, the size of each tile has an inseparable effect on the effect and use of the tiles. To know that once the tile is found to have problems and then want to rework, it can become a problem.

1. What is the shop? This question is the most basic, we must first fully understand the type of space tiles used. The key to this issue is not what to use, but how to match various materials. For example, if you want to tile in the living room and choose wood flooring in the bedroom, the problem arises: If the living room is covered with ordinary vitrified tiles and the bedroom is paved with laminate flooring, there will be a height difference of about 3cm between the bedroom and the living room. It is due to the lack of keel under the laminate floor. Usually, solid wood floors are installed by manufacturers and 3 x 2 cm keels are used. If the size of the 5 x 4 cm keel is best used for leveling with the tiles in the living room, the service terms for replacement keel of different floor manufacturers are different, so these need to be done. Good enough communication.

2. What kind of floor tiles are selected? The current floor tiles, especially those used in the living room, are mainly 500mm, 600mm, 800mm and 1000mm (i.e. 1m), among which the most used are 600mm and 800mm. How to choose?
It is recommended to choose according to the area of ​​the paving and the placement of the furniture. Since 600mm bricks per unit area have more bricks than 800mm bricks, the space can be expanded visually. At the same time, the waste rate when laying corners is lower than 800mm bricks, while the space is large 800. Even 1 meter bricks look atmospheric. Therefore, it is recommended that the space of less than 40 square meters choose 600mm specifications of the floor tiles; and more than 40 square meters of space can choose 800mm or one meter of floor tiles.
It is worth noting that if you have too much furniture (such as a bedroom) in your room and you cover a large piece of floor, it is best to use a 600mm floor tile.

3. What kind of brick antique tiles in the shop are natural and soft, and invincible in the retro style, especially in the parquet. At the same time, due to the protection of the surface glaze, it is resistant to the pollution of tea, ink and even hot cigarettes. The ability is also better than glass tiles. However, vitrified tiles are not without merit. With the development of technology, the vitrification and smoothness of the vitreous layer on the surface of vitrified tiles are already quite high. They not only make the living room look brighter, but also will not be affected by external forces like glazed tiles. , Friction produces glazed damage. So what kind of brick to choose should be determined according to the style you want to embody: To be bright and atmospheric, choose polished tiles; to choose natural and warm rustic tiles.
It is suggested that the living room and living room should be made of relatively limited choice of vitrified tiles, while the well-lit living room and non-slip kitchen and bathroom floors, balconies, etc. can be used for antique or other glazed tiles.

4. What is "Micro Crystal Jade", "Micro Crystal Stone" and "Micro Crystal Diamond"
A lot of people visiting the building materials city may be the most troublesome record tile name. What "microcrystalline jade", "microcrystalline stone", "microcrystalline diamond", "super cool stone", "polycrystalline jade" and so on. In fact, they describe the same kind of thing - vitrified bricks. These names are just the codes used by manufacturers to differentiate the products and further refine the market. When choosing, just stick to your budget and try your best to choose the right product for you.
Microcrystalline stone surface is very beautiful, but its hardness is only about 5 degrees Moh, not wear, not suitable for use on the ground and more suitable for dry hanging on the outside wall.

Tiles Living Room Space Furniture Home Furnishing Floor Tiles Antique Floors Antique Furniture Antique Tiles Bathroom Tiles Bathroom Tiles Exterior Tiles Tiles Specifications Kitchen Tiles Microcrystalline Tiles Balcony Tiles Small Bedrooms Floor Tiles

Self Tapping Screws

Because of its self forming or tapping the thread matching it, it has high anti loosing ability in combination and can be disassembled. In the small screw, its size, thread type, head type, drilling performance, in the engineering use of high tension, single, unilateral combination features almost unlimited. Self tapping materials can be divided into carbon steel and stainless steel, of which 1022 medium carbon steel is the main material.

1: According to the different head, it can be divided into: round head, flat head (i.e. countersunk head), top stigma, round top wide side head, big round head (i.e. big flat head), hexagon bearing hole head, hexagon bearing hole Huasi head, hexagon bearing hole Huasi head

Round head: it is the most commonly used head shape in the past

Flat head: it can replace the new design of round head and mushroom head. The head is low in diameter, and the peripheral circumference of the head is connected with the high edge of the characteristic, which makes it play a driving role for high-strength torque. It is slightly different from the hole head in head shape

Top column head: the diameter of the standard flat round top column head is smaller than that of the round head, but it is higher due to the groove depth. The smaller diameter increases the pressure acting on a small area, and can be closely combined with the flange and the increased surface layer. As the head is made in the drilling die set to ensure the concentration, they can be successfully applied to the holes in the internal drilling

Dome wide side head: due to the undercutting of the head to restrain and reduce the wear of the wire components, it is most commonly used in electrical appliances and tape recorders, providing an attractive design type for the middle and low head type with its more sufficient bearing surface

Big round head: also known as oval top wide edge head, is a low type, cleverly designed large diameter head. When the combined tolerance of additional function allows, it can be used to cover the metal plate hole with larger diameter. It can also be recommended to use flat head instead

Hexagon socket head: a kind of joint with the height of wrench head and the size of hexagon head. The hexagon is completely cold formed by the reverse hole mold, and there is an obvious depression at the top of the head

Hexagon socket head: such as the standard hexagon socket head, but at the same time, there is a socket face on the base of the head to protect the assembly from damage of the wrench. Sometimes the function of things is far more important than appearance

Hexagon head: This is a standard type of torque acting on the hexagon head. It has the feature of trimming sharp corners close to the tolerance range. It can be recommended for general commercial use. It can also be applied to various standard patterns and various thread diameters. Because of its necessary second process, it is more expensive than general hexagon socket

2: According to the groove type, there are four types: slotted head type (also called slotting), cross slotted head type, cross slotted head type, cross slotted compound slotted head type and meter slotted head type

3: According to the standard can be divided into: GB, DIN, ANSI, BS

Self Tapping Screws,Cross Self Tapping Screws,Big Head Self Tapping Screws,Phillips Pan Head Self Tapping Screws

Suzhou Gubao Screws Co.,Ltd. , https://www.gbscrewes.com