For a long time, the bathroom tiles will appear loose or even fall off, it is very annoying, then what are the reasons for the loss of tiles? How to prevent it? Xiaobian said to everyone today, I hope I can help you! First, the floor of the bathroom tile paving Laying non-cemented floor tiles on the ground, knocking them out, spreading the grout to the floor tiles, and laying them on the ground, with the four bricks flush in the diagonal position. The laying of the order is also stress. Posted floor tiles should be posted from the inside, such as the ground slope or floor drain, should pay attention to find the slope by the drainage direction; wall tiles should be laid up from the bottom, for the sake of beauty, the bottom of the brick should be posted. After pressing the tiles, press the tiles. In addition, a wall cannot be attached to the top at a time to prevent the tile from being heavy and causing it to fall. Do not step on tiles for a short period of time. Second, before the bathroom tile laying more water In the summer, because the material is drier than ordinary, so for the tiles, tiles and other materials that need to be treated with swelled water, the treatment time of the swelled water should be prolonged to bring the moisture to saturation. In this way, the phenomenon of water absorption from the cement due to the drying of the tiles due to the drying of the tiles will not occur, and the cement will not be firmly bonded to the tiles, causing hollowing and falling off, and will bring you some unnecessary troubles. Third, the bathroom wall tiles should be fully submerged Because wall tiles have a high moisture content, this feature must be considered when pasting. Before the tiling, the base layer should be fully watered and wet; otherwise, the moisture in the mortar will be rapidly absorbed by the dried base and tiles, and will quickly condense, which will affect its adhesive fastness. Otherwise, the tiles will absorb moisture from the cement so that the cement cannot function as an adhesive. Fourth, cleaning the base layer before tiling If the wall has lime plaster, latex paint, wallpaper and other decorative objects, or dirt on the ground, be sure to clean, otherwise the cement mortar and the grass-roots bond is not strong; In addition, if the wall itself has cracks, should do properly After processing, tiles can be used to prevent cracks or cracks in the wall bricks from increasing the cracks in the basic structure in the future. Also, for the ground and wall surfaces where the flatness or verticality gap is too large, cement mortar should be used for leveling treatment. The difference in the color of the tiles is also compared before the shop. Tips: More practical decoration knowledge, real scene with the shoot, please pay attention to the palm of this site (micro signal: mall_jia). Bathroom Tile Tiles
â… .DESCRIPTION
Aluminum Bitumen Butyl Tape is a cold applied self adhesive aluminum backed flashing in tape form.
â…¡.USES
Window and door openings (headers, sills,jambs, thresholds, nailing flanges)
Deck-to-wall intersections
Corner boards
Wall-to-wall tie-ins
Foundation sill plates
Sheathing panel seams
Under stucco finishes
Masonry walls
Roof detail areas
Gutters
Mobile home repair
Other building joints.
Exposed pipelines protection.
â…¢. COMPOSITION
High melting point polymer bitumen adhesive laminated to a 30-70 micron aluminium. The adhesive surface is protected by a release coated plastics film which is discarded during use.
â…£.Features
Easy application-Installation fast and easy-simply remove the release film and press onto the substrate.
Superior adhesion capabilities-Creates a strong bond to the substrate for long-lasting waterproofing
Protection.
Excellent sealing performance-The specially formulated rubberized asphalt adhesive seals around fasteners, allowing no water to penetrate and get to the substrate.
Highly conformable and flexible-Can accommodate settlement and shrinkage movement.
Long-lasting waterproofing protection-Both the aluminum surfaced polyethylene film and pure alu surface with the specially-formulated rubberized asphalt components create a water and moisture barrier that does not degrade from the effects of the environment.
â…¤.Technical Datas:
Waterproofing Wrapping Tape, Waterproof Aluminium Bitumen Flashing Tape, Alu Flashing Tape Jining Xunda Pipe Coating Materials Co.,Ltd , http://www.pipe-wrap.com
