The bathroom is the key project of home decoration, and it is also the place where decoration is more prone to problems. If there is slight carelessness, it may cause serious problems of water leakage and it is annoying. The bad waterproofing practices in the bathroom have a great impact on the quality of life in the future. Waterproof practices for toilets and bathroom waterproofing specifications are what most owners do not understand and are most wanted to know. Here I will tell you in detail the toilet waterproof practices and bathroom waterproof specifications. Bathroom waterproof coating 1, using paint waterproof The place of ordinary residential toilets is small, and there are pipelines and floor boards, etc. Therefore, the paint is often used for waterproofing but rarely for waterproofing. 2, two kinds of bathroom waterproof coating The material used today for waterproofing is generally paint, while the asphalt-based waterproof paint is basically not used. The following are two types of paint commonly used in bathroom waterproofing. (1) Synthetic polymer polyurethane waterproof coating (polyester cloth, fiberglass cloth, etc. for corners, etc.) (2) SBS waterproof coating of polymer-modified bitumen (adding carcass reinforcement, polyester fiber cloth, fiberglass cloth, etc.). Bathroom waterproof practices 1, waterproof construction should be used for coating waterproof material. 2. The performance of waterproof material shall comply with the relevant national standards and shall have a product certificate. 3, the surface of the grass-roots level should be flat, without hollowing, sanding, cracking and other defects. The base layer moisture content should meet the construction requirements for waterproof materials. 4, waterproof layer should extend from the ground to the wall, 250mm above the ground. The height of the waterproof layer on the bathroom wall should not be less than 1800mm. 5, waterproof cement mortar leveling layer and the base combination of dense, no hollowing, the surface smooth and smooth, no cracks, sand, yin and yang angle made of arc-shaped. 6, the coating waterproof layer brushing uniform, thickness to meet the requirements of product specifications, the general thickness of not less than 1.5mm not exposed. 7, the use of construction joints should be connected in the direction of water, lap width of not less than 100mm, the use of more than two layers of glass fiber cloth when the upper and lower overlapping lap width should be one-half. 8, the film surface is not blistering, non-flowing, smooth without bumps, and pipe fittings, sanitary fittings, floor drain, drain joints tightly closed sleek does not leak. 9, the thickness of the protective layer of cement mortar, strength must meet the design requirements, the operation is strictly prohibited damage to the waterproof layer, according to the design requirements to do a good ground flooding slope, drainage should be smooth, there must be no backwater slope phenomenon. Toilet waterproof practice height First, the toilet floor waterproof decoration height. The waterproofing of the bathroom floor is the most important part of our bathroom decoration, so the waterproof height of the ground must be refined. Bathroom floor waterproof height, usually we choose to use reinforced concrete floor pavement, 1:3 cement mortar to find the slope layer, the minimum thickness of the ground must also be 20mm thick, 30mm thick dry cement mortar combined layer, slope to floor drain, Once wiped. Second, the height of the bathroom wall waterproof decoration. For the height of the waterproof wall, a waterproof height of 30 cm is generally required. When the wall is not load-bearing, the waterproof height of the entire wall should be at least 1.8 meters. Wall waterproof paint to do about 30cm high, to prevent the accumulation of water infiltration wall surface dampness. The height of the bathroom wall of the shower room is generally 180cm; there is a bathtub, and the height of the wall adjacent to the bathtub should be 30cm higher than the height of the bathtub. Third, the bathroom floor tiles waterproof decoration height. The installation of floor tiles is an important part of our bathroom's waterproofing. In addition to laying a floor tile, we must make a waterproof layer under the surface. We should use cement mortar to level the floor and apply a waterproof coating. When the waterproof layer of the floor tile is in contact with the wall, it should be upward. From above, about 25~30cm above the ground. The height of the bathroom's sewer's waterproofing is related to our future health problems. Therefore, when handling it, one thing is to prevent the odor in the drainage pipe from overflowing into the interior of the sewer to prevent the sewer from plugging. Fourth, bathroom washbasin, urinal waterproof decoration height. The wall of the bathroom that is in contact with the washbasin is 300mm above the washbasin; if your toilet is not a toilet but a toilet bowl, then it has a waterproof height of 1800mm above the floor. The pipe (including the casing) that passes through the floor in the bathroom shall have a waterproof height of approximately 100 mm from the root of the pipe. Bathroom waterproof practices 1, bathroom waterproof height: must be waterproof wall, before the wall tiles, make the wall waterproof. In the general waterproofing process, the wall surface is to be waterproofed to a height of 30 cm. However, for a non-load-bearing lightweight wall, the entire wall should be waterproofed, and at least 60 cm in height must be achieved. 2, the bathroom waterproof smear: the seam between the wall and the ground and the pipeline between the ground and water seams, is the most prone to problems, we must urge the workers to deal with these edges and corners, a certain waterproof coating Apply it in place. 3, bathroom waterproof tile: re-floor tiles to do the floor waterproof If you need to replace the original floor tiles of the bathroom, after the original floor tiles are chiseled away, be sure to use the cement mortar to level the floor, and then do the waterproof treatment, so as to avoid the waterproof coating Leakage due to uneven thickness. Before you do waterproofing, be sure to clean the floor. 4, bathroom waterproof mulch: as far as possible without destroying the original waterproof layer in the new delivery of the general floor of the building have done a waterproof layer, so does not damage the original waterproof layer is generally not leakage. Requires the decoration team to do a good job of cement lining for the upper and lower water pipes of the toilet. Brush up 10 to 20 cm of waterproof paint from the floor, and then re-do the ester waterproofing on the ground. Add the original waterproof layer to form a composite waterproof layer to enhance waterproofing. Sex. 5, bathroom waterproof wall groove: the inner water pipe groove should also be waterproof, the construction process in the pipeline, floor drain, etc., when crossing the floor, the waterproof layer around the hole must be carefully constructed. Buried water pipes in the wall, so that a reasonable layout, the laying of water pipes will be greater than the diameter of the groove, smooth plaster groove, and then brush the groove waterproof coating. Editor's summary: The above is the introduction of knowledge related to bathroom waterproof practices, hoping to help those who have this need! For more information, please continue to pay attention to our website, follow-up will show more exciting content. You can also purchase more of your favorite products on Qijia Mall! Toilet Waterproof Practice Toilet Waterproof Specification Toilet Waterproof Partitioned Bathroom Waterproof Toilet Waterproof Remedy Toilet Waterproof Four Axis Machining Service,Five Axis Machining,Four Axis Machining,Five Axis Machining Service Lizhi Precision Manufacturing Technology Co.,Ltd , https://www.lizhihardware.com