How to properly install the bathtub

The bathtub is a large part of the bathroom. During the installation process, a little carelessness will cause a lot of trouble, so the installation method of the bathtub should pay special attention. So how to install the bathtub? What are the installation methods for the bathtub? Next, Jiuzheng Building Materials Xiaobian will answer these questions for you.

The first is to choose the right size bathtub according to the specifications of the bathroom. I believe that everyone will notice that the size of the bathtub is chosen according to the size of the bathroom. Therefore, in the early stage of installation, the size of the bathtub and the reserved space of the bathroom must be compared.

Before installing the bathtub, the bathtub should be cleaned. Remove the screws from the legs with the legs first, insert the slightly inserted mother into the bottom groove of the bathtub, buckle the legs on the bathtub, bring the nuts, and tighten the leveling. When the bathtub is brick-laying, the brick legs should be built, the cement mortar should be smeared, and the bathtub should be placed on the brick platform to find the level; if the bathtub and the brick table do not match, it can be filled with cement mortar.

When installing the bathtub into the water, put the three-way nut of the bathtub into the horizontal pipe of the lower water, wrap the asbestos rope, insert the middle of the tee, tighten the nut, insert the copper pipe into the lower water pipe mouth, and bend the lower end of the copper pipe. Put the rubber pad on the bottom of the bathtub, apply the putty, insert the hole in the bathtub, put on the rubber pad and the eye ring on the outside, and apply the lead oil, wrap and ash on the thread. Use a fork to catch the cross ribs in the drain and the water in the elbow. Put the overflow riser on the nut, wrap the oil pan rope, insert the upper opening of the tee, align the overflow hole of the bathtub, tighten the nut, add 1mm thick rubber pad to the elbow of the overflow pipe, apply putty, and wear the bolt Over the long pipe, the "one" thread on the water elbow is not loose. The bathtub is connected to the tee and the down pipe, and the oil asbestos rope is wound around the concrete. Then, the putty is tightly sealed.

Installed on the water, when installing the long neck faucet in the bathtub, such as the cold water nozzle on the wall, first straighten the upper water pipe with a short pipe, measure the short section size, saw the pipe thread, and put a smear on the twine. , screw into the nozzle, tighten and straighten, remove the hemp. For example, when installing the water mixing nozzle with a shower, remove the cold and hot water pipe plugs, put a short pipe with a threaded thread into the pipe mouth, level the alignment, and screw the mixing water inlet to the lead oil. Insert the key into the inlet, put it into the cold and hot water nozzle, check the size, protect the mouth against the wall, then align the mixing nozzle, tighten the nut, level the alignment, make the mark after the fit, and mix the water gate Remove, re-smear the oil and wrap it and install it.

Jiuzheng Building Materials Network Xiaobian reminder: As long as everyone pays attention to the above problems when installing the bathtub, it will avoid a lot of trouble, I hope to bring help to everyone.

Basin Taps

Browse our basin taps and mixers to give your washbasin a new lease of life.

Our range of bathroom taps and mixers are available in a gorgeous choice of designs. Choose from a range of contemporary or traditional basin taps or Bath Taps, or if you are looking for something a little more modern, select from our range of deck mounted or wall mounted basin and bath mixers which deliver water through a single spout. For the ultimate flexibility, also take a look at our range of bath shower mixers. Our bathroom taps and mixers combine exceptional quality design with real value for money. Selected products in the range also include clever flow limiting devices to help save water. Taps with lever handles have also been designed to be easy to use and some of our ranges are suitable for low pressure.

Basin Mixer Tap, Bathroom Basin Tap, Double Handle Basin Tap, Single Handle Basin Tap

ZHEJIANG KINGSIR VALVE CO., LTD. , https://www.kingsirvalves.com