One of the key words of the tile machine assembly, level

Songzheng Machinery Technology Show
Botou Songzheng Cold Bending Machinery Factory (http://) Li Guangtao (13613270086)

The assembly of the tile press is a very rigorous work, and the assembly accuracy is directly affected by the mechanical properties and working conditions of the tile press. After assembling the assembly process, the assembly staff of Songzheng Cold Bending Machinery Factory compiled a set of “Washing Machine Assembly Process Flow”. This article made a brief explanation on one of the key points of “leveling”, in order to help customers better. The identification and judgment of the quality of the tile machine helps customers to purchase cost-effective equipment.

Most of the work of the tile press is balanced and symmetrical. How to “level” is a key point in the assembly work, summarized as follows:

1. The big frame is leveled. After the welding is completed, it will be allowed to stand for a period of time (usually 24 hours) and enter the leveling section. The horizontal leveling is generally used for leveling. Before leveling, place the large frame on the assembly level, then grind off the welding slag, iron tumor iron slag and dust on the large frame. Use the level ruler on the nose, the tail, the middle of the frame and the reinforcement beam. Level the area. After leveling, fix with a horn.

2. The bottom of the shaft is leveled flat. When finding the bottom, first fix the bottom of the two rows of shafts at the end of the machine, and pull the wire from the end of the machine. The thinner the line, the higher the accuracy. Adjust the bottom of each row in turn, and adjust the bottom screw when adjusting. The horizontal line should be slightly below the flat standard line and tighten the fastening screws. Complete the bottom adjustment of each row of axes in turn.

3. Level adjustment of the upper row of shaft rows. The adjustment of the upper row of shaft rows is mainly the control of the upper and lower circumferential gaps. Generally speaking, after the bottom level of the lower row of shafts is adjusted into position, the level of the upper row of shafts is relatively easy to adjust. While adjusting the gap between the upper and lower shafts with the feeler gauge, the level of the upper row of shafts has been determined, but care must be taken to tighten the tightening screws. Otherwise, the gap will be reduced after tightening.

4. Feeding frame level adjustment. Firstly, determine the upper and lower dimensions of the feeding frame. Place the level on the horizontal surface during welding, and adjust the horizontal and vertical directions during welding. Make sure the feed rack is level before, after, and so on.

5. Cutting head level. After the cutting head adjusts the upper and lower positions of the knife edge, temporarily fix it with the adjusting screw, and then adjust the left and right and front and rear levels of the cutting head with the leveling ruler. When adjusting, use the adjusting screw to adjust the diagonally. After the front, rear, left and right are horizontal, tighten with the fastening screws.

The above is a problem that needs to be paid attention to in the “leveling” process of the flat plate pressing machine during assembly. The level of “leveling” is the standard for experiencing the level of assembly of a manufacturer, and it is also the standard for testing the quality of a device. It is also a parameter indicator that customers should pay attention to when selecting a tile press.
Http://news.chinawj.com.cn One of the key words of the tile machine assembly, level Submission: 'One of the key words of the tile machine assembly, level

SPR rubber Vertical Slurry Pump

Naipu SPR rubber Vertical Slurry Pumps are vertical, centrifugal slurry pumps submerged in sump to work.They are designed for delivering abrasive,large particle and high density slurries.These pumps have no need of any shaft seal and sealing water. They can also be operated normally for insufficient suction duties.Wet parts of type NP-SP pump are made of abrasion-resistant metal. All parts of type NP-SP(R) pump immersed in liquid are lined with rubber outer liner.They are suited to transport non-edge angle abrasive slurry.

Typical Applications---

Sump drainage washdown
Floor drainage
Mill sumps
Carbon transfer
Monitoring

Magnetite mixing

NP-SPR Construction Drawing

Showing Component

Main Part Number At The Drawing

1.Discharge Pipe
2.Column
3.Strainer
4.Back Liner
5.Impeller
6.Pump Casing
7.Lower Pipe


Materials of Construction

IMPELLERS

CASING

COLUMN

DISCHARGE

SEALS

Standard

High Chrome Alloy Rubber

High Chrome Alloy Rubber

Mild Steel
Mild Steel Rubber Lined

Mild Steel
Mild Steel Rubber Lined

Natural Rubber
Rubber

Options

Butyl
EPDM
Hypalon
Polyurethane
316 SS
W 151

Neoprene
Butyl
EPDM
Hypalon
Nitrile
316 SS
W 151

Neoprene
Butyl
Nitrile
316 SS

Neoprene
Butyl
Nitrile
316 SS

Nordel
Neoprene
Viton
Hypalon
Butyl
EPDM


Selection Chart

Selection Chart

SP SUMP PUMP PERFORMANCE PARAMETERS


Type

Allowable Mating Max. Power(Kw)

Range Of Performance

Impeller

Capacity/Q

Head/m

Speed/rpm

Max Efficiency/%

No. of Vanes

Impeller Diameter/mm

m³/hr

L/S

40PV-NP-SP

15

19.44-43.2

5.4-12

4.5-28.5

1000-2200

40

5

188

65QV-NP-SP

30

23.4-111

6.5-30.8

5-29.5

700-1500

50

5

280

100RV-NP-SP

75

54-289

15-80.3

5-35

500-1200

56

5

370

150SV-NP-SP

110

108-479.16

30-133.1

8.5-40

500-1000

52

5

450

200SV-NP-SP

110

189-891

152.5-247.5

6.5-37

400-850

64

5

520

250TV-NP-SP

200

261-1089

72.5-302.5

7.5-33.5

400-750

60

5

575

300TV-NP-SP

200

288-1267

80-352

6.5-33

350-700

50

5

610




Spr Rubber Vertical Slurry Pump,40Pv Rubber Slurry Pump,65Qv Rubber Vertial Pump,100Rv Rubber Slurry Pump

Shijiazhuang Naipu Pump Co., Ltd. , https://www.naipu-pump.com