On the day of the assault by the owner, it happened that the masters were also reconciling the primer and brushing the panels of the cabinet. After communicating with the master, the construction process was recorded and posted to learn and exchange with the students. (The following process is for reference only, whichever is the case) Clear water is painted with transparent or translucent paint to see the original wood grain. Mixing water is to completely cover the original wood grain and color of the wood with opaque colored paint. Today mainly said is mixed water primer brushing: Wooden paint mixed water construction process: The first step is to clean the dirt on the wood first The second step, brush the first time paint The third step is to dry the fourth step with sandpaper after drying and brush the second time The eighth step, dry the sand with a sandpaper and paint the third step Really understand the concept of mixing water and clear water: Mixing water, that is, regardless of the original wood, can be covered with their favorite colors. The requirements of wood are not high, and can keep up with the era of popular colors. Therefore, loved by young friends. However, due to, The paint completely covered the original texture of the wood, making the home lack the natural wilderness, lost the original affinity of wood, so, over time, always look at a color, it will feel bored. So, a lot People chose "clean water." The clear water coating can fully reflect the natural wood texture. Therefore, the requirements for wood are also particularly high. At the same time, the woodworking process is also required to be better. Therefore, the general construction unit prefers to do "mixed" and disliked "clean." However, because the texture of the natural wood rings is clearly presented to you, the feeling is that any color "water mixing" cannot be achieved. In the era of people advocating nature, it can give you a natural wild charm when you Carefully admiring the uncanny natural wood grain, imagine the hardships it grows from a small seedling into a tall tree, a kind of natural affinity will arise spontaneously. However, due to the relatively poor corrosion resistance of transparent paint, often comparing It is easy to yellow, and the color is not bright and colorful. Therefore, it is generally respected by middle-aged people. Attach the water lacquer construction process: (Construction process is much the same, all the construction process is only for the reference of netizens, not as a construction standard, everything is based on the actual situation) 1. Water lacquer process Step 1: Apply colored oil or toning oil. (Note: limited to projects that require discoloration, this process is not required for ordinary projects) If there is no previous process, this is the first process. If the original color is used for varnishing, then after the material is purchased in the construction site, the surface must be cleaned and the first pass of the protective primer, primer and topcoat must be carried out immediately. The same in nature. * The varnish finish must be treated before the wall paint is applied. Step 2: Clean the wood surface of dust and dirt. Step 3: Use sandpaper to polish the surface of the board or wood. Step 4: Brush the first time finish. Step 5: After drying out, use the formulated toner, cooked powder*, and fly powder* to reconcile the putty* to disguise the eyes and tree studs to make them resemble their natural colors. Step 6: After the drying process, polish the rough part of the toner with fine sandpaper. This is a critical step. Be sure to light the surface. Part 7: Brush the paint over again. Step 8: Dry sand and sand. Step 9: Brush again. (that is, paint sandpaper after the paint is applied again, and so on. If there is a special primer, change the first pass to a special primer) Step 10: Wipe the surface of the woodware with a damp cloth first, then wet the surface with sandpaper, and then polish the surface, commonly known as a watermill. Step 11: Brush the finish last time. In general, counting the last process, a total of about 4 to 8 passes will be required to have a superior quality. The more surface paints the better, but generally not more than 10 times. In the wet weather construction, the paint film will be whitish. The addition of nitromagnetized white water with a diluent amount of 10~15% can eliminate it. Three trees paint paint paint home cabinet Led Digital Kitchen Alarm Clock,Kitchen Timer,Digital Timer For Kitchen,Cooking Alarm Timer Chengdu Augus Science Technology Co., Ltd. , https://www.vluckyaugus.com
Brush varnish protection primer.