Stones are prone to shadowing, re-alkali, frosting, rust, oil spots, yellow and yellow weather, aging, fading, and gloss wear. Once a problem occurs, it is difficult to recover. It is the best policy for stone conservation to take preventive measures and maintain the beautiful appearance of the stone. The following is a look at what the stone cleaning protection treatment method is. Stone protection construction method Stone protection construction methods are: brush (with a brush), coating (using a sponge), rubbing (with a cloth), spraying (with a low pressure spray gun), soaking (with soaking tank), roller coating (with roller), pouring ( Seven types of containers are used. During construction, the method of protective construction must be determined according to the type of stone finishes and related protective agents. (1) Spraying: This construction method is characterized by fast construction and uniform coating, and is especially suitable for the construction of mushroom surface stone. However, it is wasteful and costly. (2) Soaking: The main advantage of this type of construction method is that it can provide sufficient protection both inside and outside of the stone, and it will not suffer from insufficient penetration like other methods. In all construction methods, only soaking can achieve the best protective effect. However, because of the large amount of stone inhalation of protective agent, the cost is higher. Therefore, it is required to use some curing agents that are of the highest quality and lower prices. Such as: Green Angel brand HB-S103 and so on. (3) Roller coating, this method is suitable for large-area ground protection construction, too much loss when used on the wall surface. Generally used for lower cost curing agent construction. (4) Rubbing, this construction process is used for the surface of the stone of Guangguang. We generally do not advocate this construction method. However, if the dose of cloth coating can be enough to protect the stone, it is still a better construction method. . (5) Sponge coating, this kind of craft is used for the surface that the stone is light, can apply protective agent more evenly. (6) Pouring, this process is suitable for all kinds of stone surfaces, but the equipment and site requirements are high. (7) Hair brush, this kind of craft is suitable for all kinds of surface, can control the dose at will, it is commonly used a kind of better construction method. Deep inside the stone can not be very effective protection. Therefore, we promote the soaking of this construction process (facing the stone factory), this construction process can make up for the lack of some protective agents. Different stone protection agents have different construction requirements. Before construction, practical and feasible construction plans should be formulated according to the use instructions of the protective agent used and the actual situation on site. In addition, the quality of stone protection has a lot to do with the quality of the protective agent, the construction process and the quality of the construction staff. Therefore, it is advisable to consult a professional stone conservation company or to deal with them during construction. This will ensure the quality of protection. Stone protection treatment method Approach: 1. Before protective treatment, the stone must be completely clean and dry before it can be constructed. 2. Apply with a brush or roller. A sufficient amount of 100 cc or more must be applied per square meter. 3. In the area where there is a gap, the drug is injected into the gap with a syringe needle so as to achieve a protective effect of saturation. 4. When applied on the surface, apply two coats. Apply evenly when applied. After the first coat is applied, wait for more than 10 minutes to allow it to penetrate completely. When applying the second coat, the dosage may be slightly increased or decreased depending on the current situation. 30 minutes after brushing, the surface is wiped clean until it is clean (the burned stone does not need to be covered with protective agent). 5. When applying on the back, apply a layer of thick coating. Apply evenly to the entire surface for 10 minutes. After application, wait for more than 10 minutes to allow it to evaporate and dry, and check whether the surface is slightly sticky or not. Film isolation, 30 minutes after brushing, before the full installation of stone works. Stone protection construction technology The general stone protection construction process is as follows: 1. Thoroughly removes dirt and dust from the stone surface to keep the stone clean and dry. 2. The stone curing agent can be sprayed, painted, brushed, poured or soaked evenly on the stone. 3. Put the stone overhead and keep it ventilated around the stone. Overhead mat materials should not be used for easy decolorization of wood, straw, etc. to avoid contamination. 4. Keep the stone dry for 24 hours. If you need to perform the second application, you can follow the product instructions. 5. After the stone surface is substantially dry, the yard can be piled up, but stones should be isolated between the stones to facilitate ventilation to facilitate the stone to continue drying. 6. Protective effect self-inspection, if found missing should immediately remedy. 7. The residue of the protective agent on the surface of the stone is cleaned (mainly glossy stone, no such step on the matte surface). Editor's summary: The relevant information on stone cleaning protection treatment methods and stone protection construction technology was introduced here for everyone. I hope this article will be helpful to everyone. If you still have something you don't understand, you can leave a message to Xiaobian at the bottom. We will answer your questions as soon as possible. High-grade stone stone cabinet decoration stone antique stone stone background wall offer
Shower Hinge is a general type
of door hinge largely applied for Glass Door, Shower Room. JIANGYI has
specialized in door hinges since 2000, our hinges could pass 24 hours neutral
salt spraying test and acid spraying test. Also, we specially use V groove spindle
to make sure glass doors accurately stop at 0°and 90°.
Specification
1. Material: Brass/ Stainless Steel/ Zinc.
Alloy
2. Finish: Mirror / Matt / Antique/ Red
copper / Gold / Rose gold
3. Suitable for glass door width:
800-1000mm
4. Suitable for glass thickness:
8-10mm, 6mm/ 12mm
5. Load weight: 45kgs
6. Automatically close at Approximately 25°
7. Must be tempered glass
Shower Hinge Shower Hinge,Glass Hinges,Shower Door Hinges,Shower Screen Hinges Jiangyi Industrial Co., Ltd , https://www.cnjyhardware.com
